As NTFS is proprietary, Apple would need a special license to use it fully on the Macs they sell.
The package has been tested with Mac OS X 10.4.11/PowerPC, Mac OS X 10.5.8/PowerPC and Mac OS X 10.6.4/Intel/64-bit Intel.
Download: NTFS-3G for Mac OS X 2010.8.8 Source code System requirements: Mac OS X 10.4/10.5/10.6 (10.6 requires that you do not use the 64-bit kernel), running on an Intel or PowerPC computer.
It’ll install cleanly and easily on modern versions of macOS, including macOS 10.12 Sierra and Mac OS X 10.11 El Capitan. Paragon NTFS for Mac costs $19.95 and offers a ten-day free trial.
The Best Paid Third-Party Driver: Paragon NTFS for Mac. They are prepared for hackers and geeks who are familiar with the command prompt, not common people who can easily mess up the system. The best alternative is Paragon NTFS for Mac OS X.
There are three alternatives to NTFS-3G for Mac OSX for Mac. Some people may suggest installing NTFS-3G or Fuse for macOS NTFS driver, but in fact, they are tricky to use. NTFS-3G for Mac OSX is described as 'NTFS-3G for Mac OS X brings NTFS read/write support to Mac OS X, along with additional advanced features' and is an app. Then reboot your Mac normally again.That’s it, your Mac now is NTFS write supported after installing iBoysoft Drive Manager. In the recovery console, open the terminal window and re-enable the system integrity using following command: csrutil enable Last but not least, you need to re-enable the system integrity protection again! Reboot your Mac into the recovery console by holding Command+R while rebooting. NTFS-3G for Mac adds drivers to your OS X installation that allow you to read and write to NTFS-formatted thumb and external hard drives as if youre using a Windows machine. Now the most important part - we need to replace the exisitng NTFS driver as follows: sudo mv /sbin/mount_ntfs /sbin/mount_ntfs.original sudo ln -s /usr/local/sbin/mount_ntfs /sbin/mount_ntfsĥ. Then link ntfs-3g with this command: brew link ntfs-3gĤ. No worries, you are in the right track! To fix that let’s create the required directory with this command in the Terminal: sudo mkdir sbinĮnable write permission in sbin directory using: sudo chown -R $(whoami) $(brew -prefix) But ntfs-3g installation may provide following error in your terminal: Error: Could not symlink sbin/ntfs-3g usr/local/sbin is not writable. If you don’t see any error / warnings you can just proceed to Step-4 skipping the rest of this step. Then install ntfs-3g: brew install ntfs-3gģ. Install osxfuse using homebrew with following command in your Terminal: brew cask install osxfuse It is based on NTFS-3G, the leading open source NTFS driver that is ported to numerous platforms, but also includes other software projects to build a complete toolset for managing NTFS volumes. In your Terminal then we are good to go for the next steps:Ģ. NTFS-3G for OS X is a software project designed to bring NTFS read/write support to the Mac platform, along with additional advanced features. System Integrity Protection status: disabled.
Open the Terminal to check if the system integrity status is disabled using this command: csrutil status Now reboot your Mac again and and let it boot normally. Open up the Terminal from the “Utilities” menu and type in the following: csrutil disable Reboot the Mac and hold Command+R at boot to get into the recovery console. We need to disable the system integrity protection first. You can install Homebrew pasting following command in your Terminal: /usr/bin/ruby -e "$(curl -fsSL )" Stepsġ.
Enable NTFS write support in MacOS High Sierra (10.13.x) Prerequisiteīefore you begin, make sure Homebrew is installed on your current system.